D-UN-DY-23 Dumps - Grab Out For [NEW-2024] EMC Exam
D-UN-DY-23 Exam Dumps PDF Guaranteed Success with Accurate & Updated Questions
NEW QUESTION # 14
A storage engineer was asked to restore a LUN snapshot using a previous copy.
What is the correct sequence of steps for a restore process?
Answer:
Explanation:
Explanation
https://www.delltechnologies.com/asset/en-us/products/storage/industry-market/h15089-dell_emc_unity-snapsho
NEW QUESTION # 15
A storage administrator must configure replication from a production Dell Unity XT 680F to an offsite DR Dell Unity XT 480. Block resources must be replicated without data loss if the production site becomes unavailable. File resources can be replicated with an acceptable amount of data difference on the destination.
What replication configuration meets the requirements?
- A. Set an RPO of 0 on the synchronous replication sessions.
- B. Configure the replication connection mode to Both.
- C. Configure the replication interfaces on the 4-port mezzanine card.
- D. Set Unisphere resource filtering to All.
Answer: B
Explanation:
Explanation
To meet the requirements, the replication connection mode must be set to Both, which allows both synchronous and asynchronous replication sessions to be configured on the same connection. This way, block resources can use synchronous replication, which ensures zero data loss, and file resources can use asynchronous replication, which allows some data difference on the destination. Setting Unisphere resource filtering to All is not necessary, as it only affects the display of resources in the Unisphere GUI. Setting an RPO of 0 on the synchronous replication sessions is redundant, as synchronous replication always has an RPO of 0. Configuring the replication interfaces on the 4-port mezzanine card is not relevant, as it only affects the performance and availability of the replication network.
References: [Dell EMC Unity: Replication Technologies], [Dell EMC Unity: Unisphere Overview]
NEW QUESTION # 16
What is a characteristic of Host Groups?
- A. Hosts added to a host group must not have mapped block storage resources.
- B. Block storage resources addedlo a host group are accessible to all the member hosts
- C. Access to block storage resources must be set before adding hosts to a host group.
- D. Block storage resources attached to one of the member hosts are accessible to the entire host group.
Answer: B
Explanation:
Explanation
A characteristic of Host Groups is that block storage resources added to a host group are accessible to all the member hosts. A Host Group is a logical grouping of hosts that share the same access permissions and settings for block storage resources. By adding block storage resources to a host group, the user can simplify the management and allocation of storage for multiple hosts. Access to block storage resources does not need to be set before adding hosts to a host group, as the access permissions can be modified later. Hosts added to a host group can have mapped block storage resources, as long as they are not in conflict with the host group resources. Block storage resources attached to one of the member hosts are not accessible to the entire host group, unless they are also added to the host group.
References: [Dell EMC Unity: Host Configuration], [Dell EMC Unity: Block Storage Provisioning]
NEW QUESTION # 17
What is the result of enabling Data Reduction on a LUN in a consistency group containing three LUNs?
- A. All writes to all consistency group LUNs will go through the Data Reduction logic.
- B. Data Reduction will be enabled on all LUNs is the consistency group.
- C. Any writes to the LUN will go through the Data Reduction logic.
- D. Data Reduction and Advanced Deduplication will be enabled on all LUNs.
Answer: A
Explanation:
Explanation
Data Reduction is a feature that reduces the amount of physical storage space required to store user data on a LUN. Data Reduction is enabled at the LUN level and applies to all the data in the LUN, including snapshots and thin clones. Data Reduction consists of two components: compression and deduplication. Compression reduces the size of data blocks by removing redundant information, while deduplication eliminates duplicate blocks across the LUN. When Data Reduction is enabled on a LUN, all writes to the LUN will go through the Data Reduction logic before being written to the storage pool. If the LUN is part of a consistency group, Data Reduction will be enabled on all the LUNs in the consistency group, and all writes to any LUN in the group will go through the Data Reduction logic. This ensures that the data in the consistency group is consistent and protected by the same Data Reduction settings. References:
Dell EMC Unity: Data Reduction Overview
Dell EMC Unity: Data Reduction Configuration and Best Practices
NEW QUESTION # 18
A storage administrator has a Dell Unity XT 480 system with one pool of flash drives, 192 GB of RAM, and
1.2 TB of FAST Cache.
What is the total cache availability for caching the flash drives?
- A. 1.39 TB
- B. I6.0 TB
- C. 3.58 TB
- D. 3.2 TB
Answer: C
Explanation:
Explanation
The total cache availability for caching the flash drives on a Dell Unity XT 480 system with one pool of flash drives, 192 GB of RAM, and 1.2 TB of FAST Cache is 3.58 TB. This is calculated by adding the system memory (RAM), the FAST Cache, and the pool cache. The system memory is 192 GB, which is equivalent to
0.18 TB. The FAST Cache is 1.2 TB, which is a dedicated cache for the flash drives. The pool cache is 2.2 TB, which is a portion of the flash drives that is reserved for caching the pool data. Therefore, the total cache availability is 0.18 + 1.2 + 2.2 = 3.58 TB.
References: [Dell EMC Unity: Performance Metrics], [Dell EMC Unity: FAST Cache Overview]
NEW QUESTION # 19
A system administrator deployed a UnityVSA to their vSphere environment. They did not add the management IP to the UnityVSA during the installation.
Which command must be used to apply the management IP from the vSphere UnityVSA console?
- A. svc_inject
- B. svc_ipmi
- C. svc_change_hw_config
- D. svc_initial_config
Answer: D
Explanation:
Explanation
To apply the management IP from the vSphere UnityVSA console, the system administrator must use the svc_initial_config command. This command allows the user to configure the initial network settings for the UnityVSA, such as the management IP address, subnet mask, gateway, and DNS servers. The svc_ipmi command is used to configure the IPMI settings for the UnityVSA, such as the IPMI IP address, username, and password. The svc_change_hw_config command is used to change the hardware configuration of the UnityVSA, such as the number of CPU cores, memory size, and disk size. The svc_inject command is used to inject faults into the UnityVSA for testing purposes.
References: [Dell EMC UnityVSA Installation Guide], [Dell EMC UnityVSA Command Line Interface Reference Guide]
NEW QUESTION # 20
Which firewall ports are required to be open for a successful outbound connection when configuring integrated secure connect gateway?
- A. 443 and 8443
- B. 9443 and 443
- C. 80 and 9443
- D. 80 and 443
Answer: A
Explanation:
Explanation
The firewall ports that are required to be open for a successful outbound connection when configuring integrated secure connect gateway are 443 and 8443. Integrated secure connect gateway is a feature that enables secure remote access to the Dell Unity system through the Unisphere Central web portal. It requires an outbound connection from the Dell Unity system to the Unisphere Central server over the internet. Port 443 is used for HTTPS communication and port 8443 is used for WebSocket communication.
References: [Dell EMC Unity: Unisphere Overview], [Dell EMC Unity: Integrated Secure Connect Gateway]
NEW QUESTION # 21
A company has an ESXi host installed with FC HBAs that is connected to a Dell Unity XT storage array. A
500 GB LUN is provisioned to this host from the Unity array and is in production. The VMware administrator has configured a new vSwitch with the NICs on the server intended for iSCSI traffic. The storage administrator is asked to configure software iSCSI and provision a new 1 TB LUN from the storage array using iSCSI.
What is a consideration when satisfying this request?
- A. A connection must be established between the host iSCSI initiators and Unity iSCSI targets before provisioning the new LUN.
- B. Any single host should connect to any single array using one protocol only.
- C. Two iSCSI target interfaces must be configured with IP addresses from separate subnets.
Answer: B
Explanation:
Explanation
Mixing FC and iSCSI protocols for the same host and array is not supported by Dell EMC Unity. This can cause issues with multipathing, failover, and performance. The best practice is to use one protocol per host and array pair. If the host needs to access both FC and iSCSI LUNs from different arrays, then separate vSwitches and port groups should be used for each protocol. References: Dell EMC Unity: Best Practices Guide1, page
19.
NEW QUESTION # 22
A company needs to expand their dynamic pool by 10 TB. The current dynamic pool consists of 63 7.6 TB SSD drives that are configured for RAID 5 (12+1).
What is the minimum number of drives needed for the pool expansion?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
Explanation:
Explanation
To expand a dynamic pool, the number of drives added must be equal to or greater than the stripe width of the pool. The stripe width is the number of data drives plus the number of parity drives in a RAID group. In this case, the stripe width is 12 + 1 = 13. Therefore, the minimum number of drives needed for the pool expansion is 13. References: Dell EMC Unity: Dynamic Pools Technical White Paper1, page 8.
NEW QUESTION # 23
Which are two ways to create an asynchronous replication session for a NAS server? (Choose two.)
- A. Create replication connect.
- B. Create replication interface.
- C. Use the NAS server wizard.
- D. Use NAS server properties.
Answer: C,D
Explanation:
Explanation
Two ways to create an asynchronous replication session for a NAS server are to use NAS server properties and to use the NAS server wizard. Both methods allow the user to select a source NAS server and a destination NAS server, and configure the replication settings, such as the RPO, the replication schedule, and the replication mode. Creating a replication connection or a replication interface are not ways to create an asynchronous replication session for a NAS server, but rather prerequisites for enabling replication between two Dell Unity systems.
References: [Dell EMC Unity: Replication Technologies], [Dell EMC Unity: NAS Capabilities]
NEW QUESTION # 24
Which are two features of the Dell UnityVSA? (Choose two.)
- A. Dynamic Pools
- B. FC Connectivity
- C. NVMe Connectivity
- D. Asynchronous Replication
- E. iSCSI Connectivity
Answer: D,E
Explanation:
Explanation
The Dell UnityVSA is a software-defined storage solution that runs the Dell Unity operating environment on a VMware ESXi server. The Dell UnityVSA provides the same features and functions as the Dell Unity hardware platform, such as block and file storage, snapshots, thin clones, data reduction, replication, and encryption. Some of the features of the Dell UnityVSA are:
iSCSI Connectivity: The Dell UnityVSA supports iSCSI connectivity for block storage access. The iSCSI protocol enables hosts to communicate with the DellUnityVSA over an IP network and access LUNs as SCSI devices. The Dell UnityVSA can support up to 64 iSCSI interfaces and up to 256 iSCSI sessions per interface.
Asynchronous Replication: The Dell UnityVSA supports asynchronous replication for block and file storage. Asynchronous replication is a feature that copies data from a source storage resource to a destination storage resource over a network at scheduled intervals. Asynchronous replication can be used for disaster recovery, data migration, or backup purposes. The Dell UnityVSA can support up to
256 replication sessions per system.
References:
Dell EMC Unity: Introduction to the Platform
Dell EMC Unity: Deploying VMware vSphere with Dell EMC UnityVSA
Dell EMC Unity: Configuring Hosts to Access Block Storage
Dell EMC Unity: Replication Technologies
NEW QUESTION # 25
An administrator notices that the communications between Unisphere and the storage system get interrupted.
Which service task should the administrator perform to fix the issue with minimal impact?
- A. Restart Management Software
- B. Reboot Storage Processor
- C. Reinitialize
C Enable SSH
Answer: A
Explanation:
Explanation
The service task that the administrator should perform to fix the issue with minimal impact is Restart Management Software. This service task restarts the management software on both storage processors without affecting the data services or the host I/O. This can resolve the communication issues between Unisphere and the storage system. Reinitialize, Enable SSH, and Reboot Storage Processor are service tasks that have more impact and risk than Restart Management Software.
References: [Dell EMC Unity: Unisphere Overview], [Dell EMC Unity: Service Tasks]
NEW QUESTION # 26
What is the correct sequence of steps to provision storage for SMB NAS clients?
Answer:
Explanation:
Explanation
The correct sequence of steps to provision storage for SMB NAS clients is:
Group hard drives into storage pools. This allows you to create a pool of storage resources that can be allocated to different types of storage objects, such as NAS servers, file systems, and LUNs.You can create different pools based on the performance and capacity requirements of your applications1 Create a NAS server for an existing pool. A NAS server is a logical entity that provides file-level access to clients using SMB, NFS, or FTP/SFTP protocols. You need to create a NAS server before you can create file systems and shares.You can specify the pool, network settings, domain membership, and other properties for the NAS server2 Create file systems and file system shares based on the supported NAS protocol. A file system is a logical container that stores files and folders on a NAS server. A file system share is a logical representation of a file system that can be accessed by clients using a specific protocol. For SMB NAS clients, you need to create SMB file system shares that support the SMB protocol.You can configure the share name, permissions, access policies, and other settings for the SMB share3 Map the shared file system to the client. This allows the client to access the files and folders on the SMB share using a drive letter or a UNC path.You can use the Windows Explorer or the net use command to map the shared file system to the client4
NEW QUESTION # 27
On a Dell Unity XT file system asynchronous replication session, how many system Snapshots are required to support replication?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
Explanation:
Explanation
On a Dell Unity XT file system asynchronous replication session, four system Snapshots are required to support replication. Two system Snapshots are created on the source file system, and two system Snapshots are created on the destination file system. The source system Snapshots are used to track the changes that need to be replicated, and the destination system Snapshots are used to apply the changes and maintain a consistent point-in-time copy of the source data. The system Snapshots are automatically created and managed by the replication engine and are not visible to the user.
References: [Dell EMC Unity: Replication Technologies], [Dell EMC Unity: File System Configuration]
NEW QUESTION # 28
An administrator has configured a Host Group to have access to a storage object.
What are two benefits of this configuration? (Choose two.)
- A. Provides multiple hosts access to the same LUNs
- B. Provides multiple hosts the same access to NFS Filesvstems
- C. Ensures that snapshots are applied to all LUNs in the group
- D. Provides multiple hosts access to the same VMFS Datastores
- E. Ensures that block storage is replicated to the same hosts
Answer: A,D
Explanation:
Explanation
A Host Group is a logical grouping of hosts that share the same access permissions to storage objects, such as LUNs, VMFS Datastores, or NFS Filesystems. By configuring a Host Group, an administrator can simplify the management of multiple hosts and ensure consistent access to the storage resources. Some of the benefits of using a Host Group are:
Provides multiple hosts access to the same VMFS Datastores: A VMFS Datastore is a block-based storage object that is formatted with the VMware File System (VMFS) and used to store virtual machine files. A VMFS Datastore can be shared by multiple hosts that are part of a VMware cluster. By adding these hosts to a Host Group and assigning the VMFS Datastore to the Host Group, the administrator can ensure that all the hosts have the same access permissions and can access the virtual machines on the Datastore.
Provides multiple hosts access to the same LUNs: A LUN is a block-based storage object that is presented to a host as a SCSI device. A LUN can be shared by multiple hosts that have the same operating system and use a cluster-aware file system. By adding these hosts to a Host Group and assigning the LUN to the Host Group, the administrator can ensure that all the hosts have the same access permissions and can access the data on the LUN.
References:
Dell EMC Unity: Host Configuration
Dell EMC Unity: VMware ESXi Hosts and Clusters
NEW QUESTION # 29
......
Get New D-UN-DY-23 Certification Practice Test Questions Exam Dumps: https://www.validdumps.top/D-UN-DY-23-exam-torrent.html
Pass D-UN-DY-23 Exam - Real Test Engine PDF with 38 Questions: https://drive.google.com/open?id=17amc6eoiSLnehpO310ZioFasdrPZ6mla